JL Audio Slash 1200/1v3 Class D Monoblock Subwoofer Amplifier 1,200 watts RMS

Pure power for your subs

JL Audio's 1200/1v3 mono subwoofer amplifier puts out 1,200 watts RMS to your subs, so you'll enjoy powerful, moving bass in your car. Its patented Class-D amp circuitry delivers exceptional, natural sound with extremely low distortion, while a parametric EQ bass boost gives you precise control over your bass. You can add the RBC-1 wired remote (not included) to dial in the right amount of thump from the front seat.

Consistent power for performance you can count on

This Slash v3 amplifier isn't just powerful, it's smart. As your car system's voltage fluctuates while you drive, the Regulated, Intelligent Power Supply™ system maintains steady, consistent power at any impedance between 1.5 and 4 ohms and at any voltage between 11 and 14.4 volts. You'll get all the power, all the time, even with a wide range of speaker combinations.

Minimize external noise

The 1200/1v3 uses "differential-balanced inputs" to isolate the signal's ground from the chassis ground, reducing noise and making this Slash v3 amplifier compatible with almost any system, including most factory radios. You can adjust the variable infra-sonic- and low-pass filters to maximize the performance of your subwoofers.

Slash 1200/1v3 control and connection panel

Product Features:

• Slash v3 Series Class D Monoblock Car Amplifier
• RMS Power Rating (11V-14.5V):
  • • • 4 ohms: 1200 watts x 1 chan.
      • 3 ohms: 1200 watts x 1 chan.
      • 2 ohms: 1200 watts x 1 chan.
      • 1.5 ohms: 1200 watts x 1 chan.
• High-Damping H-Bridge, Class D Mono Circuit
• R.I.P.S. - Regulated, Intelligent Power Supply
• Pulse width modulation-regulated switching power supply
• LED power/thermal/low-impedance/low-voltage indicators
• Differential-balanced input type with RCA jack inputs
• Speaker level inputs via RCA, JL Audio XD-CLRAIC2-SW required
• Single-band, fully parametric equalizer with "Q" and boost adjustment
• Preamp RCA outputs w/ crossover filter options
• Remote bass port input (JL Audio RBC-1 sold separately)
• Input sensitivity:
  • • • Low level: 200mV-2V
      • High level: 800mV-8V
• State-variable, 12 dB/octave Butterworth or 24 dB/octave Linkwitz-Riley LPF
• Variable low-pass filter: 40 - 200 Hz
• Fully variable, 24 dB/octave Butterworth HPF
• Advanced Bass Control:Subsonic ("Infrasonic") Filter: 15 - 60 Hz
  • • "Q" Bandwidth Control: 0.5 - 4.3
    • Center Frequency: 20 - 85 Hz
    • EQ Boost Control: 0 - +15 dB
• Selectable output frequency mode: LP / HP
• Selectable output frequency slop: 12 dB / 24dB
• Output filter cutoff frequency: 40 - 200 Hz
• Total Harmonic Distortion: <0.05% @ 4Ω , 50 Hz
• Signal to Noise Ration: >95 dB
• Frequency response: 5 - 250 Hz (+0, -3 dB)
• Damping Factor: >500 @ 4Ω/50 Hz, >250 @ 2Ω/50 Hz
• Inline 100A x 1 ANL or MaxiFuse Recommended
• Dimensions: 19.70"L x 9.25"W x 2.36 "H
• 4 gauge OFC power and ground wiring are recommended for installation.
• UK Internet Dealer
• Manufacturer's Warranty

What's in the box: