Automatic high-fidelity
Now you can get fantastic, high-fidelity sound without shelling out a lot of money for complicated gear or spending too much time tuning the system after installation. Kicker's KEY200.4 compact car amplifier features automatic signal processing that tailors the sound for your specific vehicle's interior space. This 4-channel compact power pack will send 50 watts RMS to each of your front and rear speakers — way more than twice the power of a typical aftermarket receiver, three or four times the power of typical factory radio.
KEY Auto Setup tunes in minutes, not hours
After installation, you set up the included calibration mic, start the test noise (downloaded from Kicker), hit the activation button, and the KEY Auto Setup software automatically sets the crossovers, 40-band EQ, and time-aligns the sound for the front seat driver. Then later, with the button, you can A/B the before- and after-processing sound, to amaze your friends and family.
Advanced features
You can manually enable Auto Compression, for more consistent and safer power output. A limiter kicks in and lights up when it detects clipping, letting you know that something's too loud. A Bi-Amp mode lets you actively run tweeters and woofers without a passive crossover, by applying customized active crossover settings during the KEY Auto Setup process.
Start-Stop problem solved
Some eco-friendly cars actually turn off their engines when stopped, and then start up again when the brakes are released. The voltage dip during starting could shut down an amplifier or allow it to pass a dangerous clipped signal to the speakers. The KEY200.4 prevents these issues by automatically engaging its limiter in these circumstances.
Integrates well
This amp's so tiny, it'll fit almost anywhere in almost any vehicle. Kicker's FIT2™ technology, using speaker-level inputs with DC offset sensing turn-on, ensures this amp will work in just about any system, even one with a factory radio. The Radio-Detect switch makes sure you never get a "No Speakers Detected" message on your receiver's display when you install this amp.
KEY200.4 with activation button and calibration mic
Product Features:
- 200 Watts of Power (50x4)
- Auto EQ Microphone with Selector Switch Included
- Compatible with Start/Stop Vehicle Technology
- FIT2 Technology Included
- Turn On Via Remote 12v Signal or DC Offset
- Auto 40-Band Equalizer
- Bi-Amp Capability (Defeatable)
- Auto Compressor (Defeatable)
- Kicker EQ Pre-set (Defeatable)
- Auto Time Alignment (Defeatable
- Auto Level Adjustment (Bi-Amp Mode Only)
- Auto Speaker Size Detection
- 24dB Crossovers
- 60/80/120Hz High Pass Filter (Defeatable)
Specification:
- Power (watts/ch), 4 Ohm stereo: 50x 4
- Microphone/Kicker EQ button: Included
- Imperial dimensions (H x W x L): 1-11/16 x 2-3/4 x 7-3/8
- Metric dimensions (H x W x L): 4.3 x 7 x18.7
- Frequency Response (Hz): 20-20k, +0/-1dB
- Input Sensitivity: High-level 250mV-10V
- Signal-to-Noise Ratio: >90dB, a-weighted, re: rated power
- Active Crossover: 24dB/octave, selective high pass or all pass @60, 80, or 120Hz
- Warranty: 1 year
What's in the box:
- 4-Channel amplifier
- 12" Power/ground/speaker output harness
- 12" Input harness
- Loop wire w/ inline fuse holder (20A fuse installed)
- Calibration microphone w/ attached 11.5' cable and inline Activation button (cable terminated in a 3.5mm TRS plug)
- 16" Rubber microphone strap
- Two 12" wire ties
- Four 1" screws
- Quickstart guide
Price | £299.99 |
---|---|
Manufacturer | Kicker |
Vehicle Manufacturer | None |